Kitchen area Cupboard Set up – Phase-By-Phase Directions on How to Put in Kitchen Cupboards Your self

Now that you have your new kitchen cabinets, you are prepared to shift on to the next large action…..Putting in your kitchen area cupboards. Although the true set up of the Kitchen Cupboards isn’tall that difficult, the essential initial phase is measuring and marking out the place the cupboards will go. By inserting layout markings on the walls and floors, it will not only aid you with kitchen cabinet placement and stud places, but it will also aid you track down where changes and shims will be necessary. Just before we get started out there are a pair of things that you will need to have for the task:


Stage or Laser Amount


Tape Evaluate

Stud Finder


one” x three” Piece of lumber (6′-8′ in duration) or an Inverted U-shaped frame (see notes beneath)


Screws (prolonged adequate to go one 1/2 into the studs)

Utility knife or chisel

Marking Compass

An added established of arms (you may possibly have to bribe a single of your friends)

As I talked about earlier mentioned, you have the choice of using a piece of 1′ x 3′ lumber for the set up or developing a frame to assist the cupboards (I have included a photo of a sample frame under). This can be created out of 2′ x 4’s and should be tall ample to assistance the base of your wall cabinets. If you plan on installing more than one particular kitchen, then I would advise the body, but a piece of lumber will do just fantastic if this is a a single time event. In either scenario, you will need to have one more established of hands to support with the set up.

In this scenario we acquired (RTA) All set-To-Assemble Kitchen area Cabinets from RTA Kitchen & Toilet Cabinet Retailer. Now the kitchen area cupboards are assembled, we are ready to commence marking out our structure lines. start off with the foundation cabinets, but we are going to begin with the wall cupboards very first. There is no appropriate or incorrect way to commence, I just choose to start off with the higher cupboards initial.

one. Use a degree and a pencil to attract a parallel line throughout the wall about 3 inches up from the ground. Measure down from this line, to the floor, and uncover the flooring large stage (if it has 1), and mark a line at that position. From that substantial level, Measure up 34 one/two inches and draw a stage line throughout the wall to designate the leading of the base cabinets.

2. Now that you have the prime of the foundation cabinets marked, evaluate up another 19 1/2 inches and a level line throughout the wall to indicate the base of the wall cabinets. Evenly mark each and every cabinets’ proportions and placement on the wall to make certain that your authentic structure is correct.

three. Use a stud finder to locate the wall studs. Use a pencil to mark the stud areas at minimum 6 inches over and under the line for the bottom of the wall cabinets. Draw straight vertical traces between the top and base marks to show the heart of the studs.

4. If you decided to go with the piece of 1′ x 3′ lumber, now is the place you will use (if you determined to go with the U-formed body, it will occur into play after all your traces are laid out). Screw a temporary 1′ x 3′ assist rail to the wall, aligning the leading edge of the rail with the line for the base edge of the wall cupboards. Attach it by driving 3 or four two inch screws through the rail into the wall studs.

5. Now that we have all the lines marked, it is time to start installing your kitchen cupboards. We are heading to commence with the corner cabinet (below is the place your helper’s added established of hands will be necessary). Area the corner cupboard on to the momentary assistance rail and have your helper keep the corner cabinet in location. Drill pilot holes by means of the sturdy cabinet back again or its help rail and into the wall studs. Screw the cupboard into the wall using two screws that are lengthy enough to penetrate the studs by at the very least 1 one/2 inches. Check out the leading of the cupboard for degree and the entrance of the cupboard for plumb. If you have to proper the place, just back the screws out a little bit and leading shims guiding the cabinet at the stud spots. If it is plumb and amount, drive the screws all the way in and include many more into every single stud to make certain that the cupboard is secured tightly to the wall.

6. Now we are heading to move onto the cupboards on possibly facet of the corner cupboard. As you put in each one particular, use the clamps to secure each cupboard to the neighboring cupboard and then verify it for plumb with your stage. On faceframe cabinets, it is a great thought to drill two 1/eight inch pilot holes by way of the sides of the faceframe and use screws. In this circumstance, with frameless, all set-to-assemble kitchen area cabinets we are likely to screw by means of the plywood sides and use shims in among the cabinets to guarantee a limited in shape and make sure that the cupboard faces are plumb.

7. Right after all the wall cabinets are in location, put in the corner or end base scenario cupboard. Use shims in which essential to degree the cupboard and raise it up to the line which signifies the substantial stage of the ground. Be positive it is stage from entrance to again and from side to side, then screw it to the wall studs. If you will not have a diagonal corner cabinet or blind foundation cupboard in the corner, push the adjoining cabinet into area and clamp the two units with each other. Insert a filler strip if needed to permit the doorways and drawers enough clearance to open up and close properly. If essential, faucet shims underneath the cabinet and driving it to adjust for plumb and degree.

8. Push screws by means of the cabinet again (and shims) into the wall studs. Trim any excess material from the shims with a sharp chisel or knife. Proceed to add adjoining cabinets in this way, signing up for them the very same way you related the wall cabinets in stage 6.

9. If your cabinets conclude up butting towards yet another wall, you may need a filler strip to make up the very last few inches. If you have custom made cabinets, they must have been built to fill this gap, but if you are using stock or RTA Kitchen area Cabinets the filler strip could be required. If you do need to have to use a filler strip, depart the last cupboard detached from the other cabinets. Clamp a straightedge to the experience of the closest set up unit, extending far adequate for you to put alignment marks on the stop wall. Enable a three/four” offset powering people marks (for the thickness of the filler piece) and fasten a cleat to the wall. Then install and fasten the final cupboard and evaluate the gap among its face body and the wall.

If the wall is flat, simply rip the filler board to the essential width and fasten it in place. If the wall is irregular, you may have to scribe-suit the filler board. Start by environment a marking compass to the width of the hole, then location a strip of one”-wide masking tape alongside the filler board in the area the place it needs to be trimmed. Clamp the board to the finish cabinet’s encounter frame, then trace the wall contour with the compass. Get rid of the board and lower along the scribe line with a jig observed, then reinstall it to check the in shape. When it truly is proper, generate screws by means of the adjacent encounter frame into the edge of the filler board. Screw or nail the other side to the cleat.

At this level, your kitchen area cupboard set up is total. If you bought matching crown molding or any other information, these should be very easily put in now. Relying on whether or not you had to use shims under the base cabinets, you might have to set up some trim pieces by the toe kicks to include up the shims or any gaps at the base of the kitchen cabinets.

I hope this helps make your kitchen cabinet installation as sleek as feasible. If you want any aid with cabinet selection, kitchen format suggestions, or suggestions for cupboard designs, examine out RTA Kitchen & Rest room Cabinet Retailer

Leave a Reply

Your email address will not be published. Required fields are marked *